AX Wall Exhaust Fan 16 inch Variable Speed 2570 CFM Direct Drive AX16-1V

Quantity	Unit Price	You Save
6-9		3%
10+		5%

All variable speed fans will run at a single speed unless used with a controller. Please see our control options here for a control that pairs with this fan.

The Canarm AX series exhaust fans are a sturdily constructed, direct drive, horizontal discharge fan that is typically used for general ventilation of factories, garages, warehouses and other industrial or commercial buildings. The AX fans are available in multiple single-speed variations as well as two-speed and variable speed models. The AX series housings are constructed of heavy duty aluminum with built in shutters that automatically open when the fan starts and gravity closes when the fan stops.

FEATURES
Variable speed motors are high efficiency motors
Can be run as single speed
These models have a rugged, sturdily constructed housing made from all aluminum extrusions
Louvers open automatically when the fan starts up and close when the fan stops
8” - 24” models have heavy wire chrome plated OSHA guards on intake side of fan
Motors are mounted on heavy gauge welded steel rod motor mounts that have a Bright Zinc finish
Totally enclosed air over motor with overload protection
Fans come fully assembled and 100% of fans are tested for proper operation before shipping

Model No.:: AX16 -1V

Voltage:: 115 / 230

Warehouse:: New York

Type:: Exhaust Fans

Amps:: 5.0 / 2.5

Blade Material:: Aluminum

Blade Size (Inches):: 16

No. of Blades:: 3

CFM High:: 2570

Decibels (dBA):: 68 @ 5ft

Dimension Inches:: Width: 20.75" Depth: 16" Height: 20.75"

Hertz:: 60

Drive Type:: Direct

Horsepower:: 1/3

Limited Warranty:: 1 Year Limited

RPM High:: 1700

Phase:: 1

Speed(s):: Variable

Weight lbs.:: 30

Notice: Manufacturer's products features and specifications are subject to change without notice.

California Residents: warning

WARNING- This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, please visit www.P65Warnings.ca.gov.

Installation Manual

Informational Manual

QUESTIONS & ANSWERS

Ask a Question

In the product details it appears the rough wall opening needs to be 17.75" sq, but in the specs its states its is 20.75" sq. Also , it states EF mounts on inside wall. Here is what I have, please indicate which fan will fit the best. I am replacing an existing louvered exhaust fan. The existing wall opening is 20.75" sq. The wall is an 8" block wall with brick veneer, so about 12" thick. I want the new fan shutters to completely cover the hole on the outside of the wall. Inside of the wall does not matter, because it is an equipment room. I would prefer to just remove the old entire fan/shutter assembly, and slide the new fan thru the hole from the outside and screw it off into the brick. Please recommend which of you products will do this. I can frame the inside of the rough opening with 1x12, or 2x12, if necessary leaving a rough opening of 19.25" or or 17.75 respectively, if required. Please advise. Thanks You may call me at 865-679-2205 if this would be easier to discuss by phone.

Thank you for your question. Here is a link to the manufacturers spec sheet on for the fan. It appears as though the shuttered, outward facing dimension of the fan housing is 17 3/4", and the mounting flange is 20 3/4". The installation guide (also linked below), says that you should be 1/2" larger than the shutter box size (allowing 1/4" on all sides for clearance). These fans are meant to be installed from the inside of the building, with the flange on the interior side of the hole.

Install - https://cdn.shopify.com/s/files/1/0972/5538/files/AX_Manual.pdf?12965407212672133746
Specs - https://cdn.shopify.com/s/files/1/0972/5538/files/AX_Series_Literature_c8053f8e-4902-4c38-9a58-308d86b72e22.pdf?v=1599075213
Can we install this for kitchen?

This wall exhaust fan can be used in kitchens for the purpose of general exhausting. This fan should not be used for high heat from stoves, or steam.

AX Wall Exhaust Fan 16 inch Variable Speed 2570 CFM Direct Drive AX16-1V

Build Time

Highly Recommended Items:

QUESTIONS & ANSWERS

AX Wall Exhaust Fan 16 inch Variable Speed 2570 CFM Direct Drive AX16-1V

Build Time

Highly Recommended Items:

QUESTIONS & ANSWERS

Similar Products To Consider